background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 1 of
9
Safety Data Sheet
Copyright,2015,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
07-2956-6
Version Number:
8.00
Issue Date:
03/26/15
Supercedes Date:
12/22/05
SECTION 1: Identification
1.1. Product identifier
3M™ Dry Guide Coat, P.N. 05860, 05861
1.2. Recommended use and restrictions on use
Recommended use
Powder applied on top of primer and plastic filler to highlight defects
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Automotive Aftermarket
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200.
This information may be different from the actual product label information for labels regulated by other agencies.
2.1. Hazard classification
Carcinogenicity: Category 2.
2.2. Label elements
Signal word
Warning
Symbols
Health Hazard |
Pictograms
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 2 of
9
Hazard Statements
Suspected of causing cancer.
Precautionary Statements
Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wear protective gloves.
Response:
IF exposed or concerned: Get medical advice/attention.
Storage:
Store locked up.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
2.3. Hazards not otherwise classified
None.
SECTION 3: Composition/information on ingredients
Ingredient
C.A.S. No.
% by Wt
Limestone
1317-65-3
40 - 70 Trade Secret *
Activated Carbon
Mixture
10 - 30 Trade Secret *
Carbon Black
1333-86-4
3 - 7 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Wash with soap and water. If signs/symptoms develop, get medical attention.
Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.
If Swallowed:
Rinse mouth. If you are concerned, get medical advice.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 3 of
9
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
During Combustion
Carbon dioxide
During Combustion
5.3. Special protective actions for fire-fighters
No special protective actions for fire-fighters are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Ventilate the area with fresh air. Refer to other sections of this SDS for information regarding physical and
health hazards, respiratory protection, ventilation, and personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment.
6.3. Methods and material for containment and cleaning up
Collect as much of the spilled material as possible. Use wet sweeping compound or water to avoid dusting. Sweep up. Place
in a closed container approved for transportation by appropriate authorities. Clean up residue. Seal the container. Dispose of
collected material as soon as possible.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Do not handle until all safety precautions have been read and understood. Avoid
breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when
using this product. Wash thoroughly after handling. Use personal protective equipment (gloves, respirators, etc.) as
required.
7.2. Conditions for safe storage including any incompatibilities
Store away from acids.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient
C.A.S. No.
Agency
Limit type
Additional Comments
Limestone
1317-65-3
OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 4 of
9
fraction):5 mg/m3
Carbon Black
1333-86-4
OSHA
TWA:3.5 mg/m3
Carbon Black
1333-86-4
ACGIH
TWA(inhalable fraction):3
mg/m3
A3: Confirmed animal
carcin.
Carbon Black
1333-86-4
CMRG
TWA:0.5 mg/m3
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Safety Glasses with side shields
Indirect Vented Goggles
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Nitrile Rubber
Respiratory protection
In case of inadequate ventilation wear respiratory protection. An exposure assessment may be needed to decide if a
respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the
results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Solid
Specific Physical Form:
Powder
Odor, Color, Grade:
Dark grey odorless powder.
Odor threshold
No Data Available
pH
Not Applicable
Melting point
No Data Available
Boiling Point
Not Applicable
Flash Point
No flash point
Evaporation rate
Not Applicable
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 5 of
9
Flammability (solid, gas)
Not Classified
Flammable Limits(LEL)
No Data Available
Flammable Limits(UEL)
Not Applicable
Vapor Pressure
Not Applicable
Vapor Density
Not Applicable
Density
0.625 - 0.770 g/cm3
Specific Gravity
0.625 - 0.770 [Ref Std: WATER=1]
Solubility- non-water
No Data Available
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
No Data Available
Decomposition temperature
No Data Available
Viscosity
Not Applicable
Hazardous Air Pollutants
0 lb HAPS/lb solids [Test Method: Calculated]
Volatile Organic Compounds
0 % weight [Test Method: calculated per CARB title 2]
Volatile Organic Compounds
0 g/l [Test Method: calculated SCAQMD rule 443.1]
Percent volatile
Nil
VOC Less H2O & Exempt Solvents
0 g/l [Test Method: calculated SCAQMD rule 443.1]
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.
10.2. Chemical stability
Stable.
10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Not determined
10.5. Incompatible materials
Strong acids
10.6. Hazardous decomposition products
Substance
Condition
None known.
Refer to section 5.2 for hazardous decomposition products during combustion.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 6 of
9
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
Skin Contact:
Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching.
Eye Contact:
Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion.
Ingestion:
No known health effects.
Additional Health Effects:
Carcinogenicity:
Contains a chemical or chemicals which can cause cancer.
Ingredient
CAS No.
Class Description
Regulation
Carbon Black
1333-86-4
Grp. 2B: Possible human carc.
International Agency for Research on Cancer
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name
Route
Species
Value
Overall product
Ingestion
No data available; calculated ATE > 5,000 mg/kg
Limestone
Dermal
Rat
LD50 > 2,000 mg/kg
Limestone
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 3.0 mg/l
Limestone
Ingestion
Rat
LD50 6,450 mg/kg
Carbon Black
Dermal
Rabbit
LD50 > 3,000 mg/kg
Carbon Black
Ingestion
Rat
LD50 > 8,000 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Name
Species
Value
Limestone
Rabbit
No significant irritation
Carbon Black
Rabbit
No significant irritation
Serious Eye Damage/Irritation
Name
Species
Value
Limestone
Rabbit
No significant irritation
Carbon Black
Rabbit
No significant irritation
Skin Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.
Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.
Germ Cell Mutagenicity
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 7 of
9
Name
Route
Value
Carbon Black
In Vitro
Not mutagenic
Carbon Black
In vivo
Some positive data exist, but the data are not
sufficient for classification
Carcinogenicity
Name
Route
Species
Value
Carbon Black
Dermal
Mouse
Not carcinogenic
Carbon Black
Ingestion
Mouse
Not carcinogenic
Carbon Black
Inhalation
Rat
Carcinogenic
Reproductive Toxicity
Reproductive and/or Developmental Effects
Name
Route
Value
Species
Test Result
Exposure
Duration
Limestone
Ingestion
Not toxic to development
Rat
NOAEL 625
mg/kg/day
premating &
during
gestation
Target Organ(s)
Specific Target Organ Toxicity - single exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Limestone
Inhalation
respiratory system
All data are negative
Rat
NOAEL
0.812 mg/l
90 minutes
Specific Target Organ Toxicity - repeated exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Limestone
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Human
NOAEL Not
available
occupational
exposure
Carbon Black
Inhalation
pneumoconiosis
Some positive data exist, but the
data are not sufficient for
classification
Human
NOAEL Not
available
occupational
exposure
Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
Ecotoxicological information
Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 8 of
9
Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste
incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty
drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations
classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes
unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the
available treatment and disposal facilities.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. US Federal Regulations
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No
Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
15.2. State Regulations
Contact 3M for more information.
California Proposition 65
Ingredient
C.A.S. No.
Classification
Carbon Black
1333-86-4
Carcinogen
WARNING: This product contains a chemical known to the State of California to cause cancer.
15.3. Chemical Inventories
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
15.4. International Regulations
Contact 3M for more information.
This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: Other information
NFPA Hazard Classification
Health: 1 Flammability: 1 Instability: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
background image
3M™ Dry Guide Coat, P.N. 05860, 05861
03/26/15
__________________________________________________________________________________________
Page 9 of
9
Document Group:
07-2956-6
Version Number:
8.00
Issue Date:
03/26/15
Supercedes Date:
12/22/05
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable
for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available
directly from 3M
3M USA SDSs are available at www.3M.com