background image
MATERIAL SAFETY DATA SHEET 3M™ Lightweight Body Filler - PN 05800, 05801, 05803, 05804, 05805, 35801
04/14/14
_________________________________________________________________________________________________________
Page 1 of
2
Material Safety Data Sheet
Copyright, 2014, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
PRODUCT NAME:
3M™ Lightweight Body Filler - PN 05800, 05801, 05803, 05804, 05805, 35801
MANUFACTURER:
3M
DIVISION:
Automotive Aftermarket
ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date:
04/14/14
Supercedes Date:
05/16/13
Document Group:
18-1856-6
ID Number(s):
LB-K100-0692-2, 41-0003-6599-3, 41-0003-6644-7, 41-0003-6664-5, 41-0003-6730-4, 41-0003-6769-2, 60-
4550-6996-7, 60-9801-0558-3, 60-9801-0559-1, 60-9801-0561-7, 60-9801-0579-9
This product is a kit or a multipart product which consists of multiple, independently packaged components. An SDS for each
of these components is included. Please do not separate the component SDSs from this cover page. The document numbers of
the SDSs for components of this product are:
29-5993-0, 32-1433-5
Revision Changes:
Section 16: Disclaimer (first paragraph) information was modified.
Section 16: Disclaimer (second paragraph) information was modified.
Kit: Component heading paragraph information was modified.
Section 16: Web address information was modified.
Section 1: Address information was modified.
Copyright information was modified.
Telephone header information was modified.
Company Telephone information was modified.
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO
background image
MATERIAL SAFETY DATA SHEET 3M™ Lightweight Body Filler - PN 05800, 05801, 05803, 05804, 05805, 35801
04/14/14
_________________________________________________________________________________________________________
Page 2 of
2
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M
3M USA SDSs are available at www.3M.com
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 1 of
14
Safety Data Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
32-1433-5
Version Number:
3.00
Issue Date:
04/14/14
Supercedes Date:
05/16/13
SECTION 1: Identification
1.1. Product identifier
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
1.2. Recommended use and restrictions on use
Recommended use
Automotive, Body Repair
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Automotive Aftermarket
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200.
This information may be different from the actual product label information for labels regulated by other agencies.
2.1. Hazard classification
Flammable Liquid: Category 3.
Serious Eye Damage/Irritation: Category 2B.
Carcinogenicity: Category 2.
Specific Target Organ Toxicity (single exposure): Category 1.
Specific Target Organ Toxicity (repeated exposure): Category 1.
2.2. Label elements
Signal word
Danger
Symbols
Flame | Health Hazard |
Pictograms
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 2 of
14
Hazard Statements
Flammable liquid and vapor.
Causes eye irritation.
Suspected of causing cancer.
Causes damage to organs:
liver |
sensory organs |
Causes damage to organs through prolonged or repeated exposure:
respiratory system |
sensory organs |
May cause damage to organs through prolonged or repeated exposure:
liver |
Precautionary Statements
General:
Keep out of reach of children.
Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
Ground/bond container and receiving equipment.
Use only non-sparking tools.
Take precautionary measures against static discharge.
Keep container tightly closed.
Use explosion-proof electrical/ventilating/lighting equipment.
Do not breathe dust/fume/gas/mist/vapors/spray.
Wear protective gloves and eye/face protection.
Do not eat, drink or smoke when using this product.
Wash thoroughly after handling.
Response:
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
If eye irritation persists: Get medical advice/attention.
IF exposed or concerned: Get medical advice/attention.
In case of fire: Use a fire fighting agent suitable for flammable liquids and solids such as dry chemical or carbon dioxide
to extinguish.
Storage:
Store in a well-ventilated place. Keep cool.
Store locked up.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 3 of
14
2.3. Hazards not otherwise classified
None.
1% of the mixture consists of ingredients of unknown acute oral toxicity.
3% of the mixture consists of ingredients of unknown acute inhalation toxicity.
SECTION 3: Composition/information on ingredients
Ingredient
C.A.S. No.
% by Wt
Polyester Resin
Trade Secret*
15 - 40 Trade Secret *
Talc
14807-96-6
10 - 30 Trade Secret *
Styrene Monomer
100-42-5
10 - 30 Trade Secret *
Magnesium Carbonate
546-93-0
7 - 15 Trade Secret *
Oxide Glass Chemicals
65997-17-3
3 - 7 Trade Secret *
Limestone
1317-65-3
1 - 5 Trade Secret *
Synthetic Crystalline-Free Silica Gel
112926-00-8
1 - 5 Trade Secret *
Chlorite (Mineral)
1318-59-8
< 5 Trade Secret *
Titanium Dioxide
13463-67-7
< 1 Trade Secret *
Quartz Silica
14808-60-7
< 0.1 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop,
get medical attention.
Eye Contact:
Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue
rinsing. Immediately get medical attention.
If Swallowed:
Rinse mouth. If you feel unwell, get medical attention.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for flammable liquids and solids such as dry chemical or carbon dioxide to
extinguish.
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 4 of
14
5.2. Special hazards arising from the substance or mixture
Closed containers exposed to heat from fire may build pressure and explode.
Hazardous Decomposition or By-Products
Substance
Condition
Hydrocarbons
During Combustion
Carbon monoxide
During Combustion
Carbon dioxide
During Combustion
5.3. Special protective actions for fire-fighters
Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and
prevent explosive rupture.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools.
Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or
exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could
cause flammable gases or vapors in the spill area to burn or explode. Refer to other sections of this SDS for information
regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.
6.3. Methods and material for containment and cleaning up
Contain spill. Cover spill area with a fire-extinguishing foam. An appropriate aqueous film forming foam (AFFF) is
recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible
using non-sparking tools. Place in a metal container approved for transportation by appropriate authorities. Clean up residue
with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow
safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Avoid breathing of dust created by cutting, sanding, grinding or machining. Keep out of reach of children. Do not handle
until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No
smoking. Ground/bond container and receiving equipment. Use only non-sparking tools. Take precautionary measures
against static discharge. Do not breathe dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do
not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid contact with oxidizing agents (eg.
chlorine, chromic acid etc.) Wear low static or properly grounded shoes. Use personal protective equipment (gloves,
respirators, etc.) as required. To minimize the risk of ignition, determine applicable electrical classifications for the process
using this product and select specific local exhaust ventilation equipment to avoid flammable vapor accumulation.
7.2. Conditions for safe storage including any incompatibilities
Store in a well-ventilated place. Keep cool. Keep container tightly closed. Protect from sunlight. Store away from heat.
Store away from acids. Store away from strong bases. Store away from oxidizing agents. Store away from areas where
product may come into contact with food or pharmaceuticals. Store in a dry place.
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 5 of
14
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
Ingredient
C.A.S. No.
Agency
Limit type
Additional Comments
Styrene Monomer
100-42-5
Amer Conf of
Gov. Indust.
Hyg.
TWA:20 ppm;STEL:40 ppm
Styrene Monomer
100-42-5
US Dept of
Labor - OSHA
TWA:100 ppm;CEIL:200 ppm
SILICA, AMORPHOUS
112926-00-
8
US Dept of
Labor - OSHA
TWA concentration:0.8
mg/m3;TWA:20 millions of
particles/cu. ft.
Limestone
1317-65-3
US Dept of
Labor - OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
Titanium Dioxide
13463-67-7 Amer Conf of
Gov. Indust.
Hyg.
TWA:10 mg/m3
Titanium Dioxide
13463-67-7 Chemical
Manufacturer
Rec Guid
TWA(as respirable dust):5
mg/m3
Titanium Dioxide
13463-67-7 US Dept of
Labor - OSHA
TWA(as total dust):15 mg/m3
Talc
14807-96-6 Amer Conf of
Gov. Indust.
Hyg.
TWA(respirable fraction):2
mg/m3
Talc
14807-96-6 Chemical
Manufacturer
Rec Guid
TWA(as respirable dust):0.5
mg/m3
Talc
14807-96-6 US Dept of
Labor - OSHA
TWA concentration(as total
dust):0.3 mg/m3;TWA
concentration(respirable):0.1
mg/m3(2.4 millions of
particles/cu. ft.);TWA:20
millions of particles/cu. ft.
Quartz Silica
14808-60-7 Amer Conf of
Gov. Indust.
Hyg.
TWA(respirable
fraction):0.025 mg/m3
Quartz Silica
14808-60-7 US Dept of
Labor - OSHA
TWA concentration(as total
dust):0.3 mg/m3;TWA
concentration(respirable):0.1
mg/m3(2.4 millions of
particles/cu. ft.)
Magnesium Carbonate
546-93-0
US Dept of
Labor - OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
Oxide Glass Chemicals
65997-17-3 Manufacturer
determined
TWA(as dust):10 mg/m3
Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists
American Indust. Hygiene Assoc : American Industrial Hygiene Association
Chemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended Guidelines
US Dept of Labor - OSHA : United States Department of Labor - Occupational Safety and Health Administration
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 6 of
14
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.
Use explosion-proof ventilation equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding
operations or when near such operations. Select and use eye/face protection to prevent contact based on the results of an
exposure assessment. The following eye/face protection(s) are recommended:
Indirect Vented Goggles
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Fluoroelastomer
Polymer laminate
Respiratory protection
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of
a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator
type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Liquid
Specific Physical Form:
Paste
Odor, Color, Grade:
Pungent Styrene Odor Grey Paste
Odor threshold
No Data Available
pH
No Data Available
Melting point
No Data Available
Boiling Point
293 ºF
Flash Point
88 ºF [Test Method: Closed Cup]
Evaporation rate
No Data Available
Flammability (solid, gas)
Not Applicable
Flammable Limits(LEL)
0.9 % [Details: based on styrene]
Flammable Limits(UEL)
6.8 % [Details: based on styrene]
Vapor Pressure
No Data Available
Vapor Density
3.6 [Ref Std: AIR=1]
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 7 of
14
Density
1.14 g/ml
Specific Gravity
1.14 [Ref Std: WATER=1]
Solubility in Water
Negligible
Solubility- non-water
No Data Available
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
No Data Available
Decomposition temperature
No Data Available
Viscosity
192,000 - 208,000 centipoise
Hazardous Air Pollutants
0.355 lb HAPS/lb solids
Volatile Organic Compounds
17.6 % weight [Test Method: calculated per CARB title 2]
Volatile Organic Compounds
200 g/l [Test Method: calculated SCAQMD rule 443.1]
Percent volatile
17.9 % weight
VOC Less H2O & Exempt Solvents
201 g/l [Test Method: calculated SCAQMD rule 443.1]
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.
10.2. Chemical stability
Stable. Stable under normal conditions. May become unstable at elevated temperatures and/or pressure.
10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Sparks and/or flames
Heat
10.5. Incompatible materials
Strong acids
Strong oxidizing agents
Alkali and alkaline earth metals
Strong bases
10.6. Hazardous decomposition products
Substance
Condition
None known.
Refer to section 5.2 for hazardous decomposition products during combustion.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 8 of
14
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
May be harmful if inhaled.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
May cause target organ effects after inhalation.
Skin Contact:
May be harmful in contact with skin.
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Ingestion:
May be harmful if swallowed.
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May cause target organ effects after ingestion.
Target Organ Effects:
Single exposure may cause:
Auditory Effects: Signs/symptoms may include hearing impairment, balance dysfunction and ringing in the ears.
Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and
jaundice.
Prolonged or repeated exposure may cause:
Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and
changes in lung function tests.
Ocular Effects: Signs/symptoms may include blurred or significantly impaired vision.
Carcinogenicity:
Contains a chemical or chemicals which can cause cancer.
Ingredient
C.A.S. No.
Class Description
Regulation
Quartz Silica
14808-60-7
Grp. 1: Carcinogenic to humans
International Agency for Research on Cancer
SILICA, CRYS AIRRESP
14808-60-7
Known human carcinogen
National Toxicology Program Carcinogens
Styrene Monomer
100-42-5
Anticipated human carcinogen
National Toxicology Program Carcinogens
Styrene Monomer
100-42-5
Grp. 2B: Possible human carc.
International Agency for Research on Cancer
Titanium Dioxide
13463-67-7
Grp. 2B: Possible human carc.
International Agency for Research on Cancer
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name
Route
Species
Value
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 9 of
14
Overall product
Dermal
No data available; calculated ATE 2,000 - 5,000
mg/kg
Overall product
Inhalation-
Vapor(4 hr)
No data available; calculated ATE 20 - 50 mg/l
Overall product
Ingestion
No data available; calculated ATE 2,000 - 5,000
mg/kg
Polyester Resin
Ingestion
LD50 estimated to be 2,000 - 5,000 mg/kg
Talc
Ingestion
LD50 Not available
Styrene Monomer
Dermal
Rat
LD50 > 2,000 mg/kg
Styrene Monomer
Inhalation-
Vapor (4
hours)
Rat
LC50 8.3 mg/l
Styrene Monomer
Ingestion
Rat
LD50 5,000 mg/kg
Magnesium Carbonate
Ingestion
Mouse
LD50 > 5,000 mg/kg
Oxide Glass Chemicals
Dermal
LD50 estimated to be > 5,000 mg/kg
Oxide Glass Chemicals
Ingestion
LD50 estimated to be 2,000 - 5,000 mg/kg
Limestone
Dermal
Rat
LD50 > 2,000 mg/kg
Limestone
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 3.0 mg/l
Limestone
Ingestion
Rat
LD50 6,450 mg/kg
Synthetic Crystalline-Free Silica Gel
Dermal
Rabbit
LD50 > 5,000 mg/kg
Synthetic Crystalline-Free Silica Gel
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 > 0.691 mg/l
Synthetic Crystalline-Free Silica Gel
Ingestion
Rat
LD50 > 5,110 mg/kg
Titanium Dioxide
Dermal
Rabbit
LD50 > 10,000 mg/kg
Titanium Dioxide
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 > 6.82 mg/l
Titanium Dioxide
Ingestion
Rat
LD50 > 10,000 mg/kg
Quartz Silica
Dermal
LD50 estimated to be > 5,000 mg/kg
Quartz Silica
Ingestion
LD50 estimated to be > 5,000 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Name
Species
Value
Talc
Rabbit
No significant irritation
Styrene Monomer
official
classifica
tion
Mild irritant
Oxide Glass Chemicals
No significant irritation
Limestone
Rabbit
No significant irritation
Synthetic Crystalline-Free Silica Gel
Rabbit
No significant irritation
Titanium Dioxide
Rabbit
No significant irritation
Quartz Silica
No significant irritation
Serious Eye Damage/Irritation
Name
Species
Value
Talc
Rabbit
No significant irritation
Styrene Monomer
official
classifica
tion
Moderate irritant
Oxide Glass Chemicals
No significant irritation
Limestone
Rabbit
No significant irritation
Synthetic Crystalline-Free Silica Gel
Rabbit
No significant irritation
Titanium Dioxide
Rabbit
No significant irritation
Skin Sensitization
Name
Species
Value
Styrene Monomer
Guinea
pig
Not sensitizing
Synthetic Crystalline-Free Silica Gel
Human
and
animal
Not sensitizing
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 10 of
14
Titanium Dioxide
Human
and
animal
Not sensitizing
Respiratory Sensitization
Name
Species
Value
Talc
Human
Not sensitizing
Germ Cell Mutagenicity
Name
Route
Value
Talc
In Vitro
Not mutagenic
Talc
In vivo
Not mutagenic
Styrene Monomer
In Vitro
Some positive data exist, but the data are not
sufficient for classification
Styrene Monomer
In vivo
Some positive data exist, but the data are not
sufficient for classification
Oxide Glass Chemicals
In Vitro
Some positive data exist, but the data are not
sufficient for classification
Synthetic Crystalline-Free Silica Gel
In Vitro
Not mutagenic
Titanium Dioxide
In Vitro
Not mutagenic
Titanium Dioxide
In vivo
Not mutagenic
Quartz Silica
In Vitro
Some positive data exist, but the data are not
sufficient for classification
Quartz Silica
In vivo
Some positive data exist, but the data are not
sufficient for classification
Carcinogenicity
Name
Route
Species
Value
Talc
Inhalation
Rat
Some positive data exist, but the data are not
sufficient for classification
Styrene Monomer
Ingestion
Mouse
Carcinogenic
Styrene Monomer
Inhalation
Human
and
animal
Carcinogenic
Oxide Glass Chemicals
Inhalation
Multiple
animal
species
Some positive data exist, but the data are not
sufficient for classification
Synthetic Crystalline-Free Silica Gel
Not
Specified
Mouse
Some positive data exist, but the data are not
sufficient for classification
Titanium Dioxide
Ingestion
Multiple
animal
species
Not carcinogenic
Titanium Dioxide
Inhalation
Rat
Carcinogenic
Quartz Silica
Inhalation
Human
and
animal
Carcinogenic
Reproductive Toxicity
Reproductive and/or Developmental Effects
Name
Route
Value
Species
Test Result
Exposure
Duration
Talc
Ingestion
Not toxic to development
Rat
NOAEL
1,600 mg/kg
during
organogenesi
s
Styrene Monomer
Ingestion
Not toxic to female reproduction
Rat
NOAEL 21
mg/kg/day
3 generation
Styrene Monomer
Inhalation
Not toxic to female reproduction
Rat
NOAEL 2.1
mg/l
2 generation
Styrene Monomer
Inhalation
Not toxic to male reproduction
Rat
NOAEL 2.1
mg/l
2 generation
Styrene Monomer
Ingestion
Some positive male reproductive data
exist, but the data are not sufficient for
classification
Rat
NOAEL 400
mg/kg/day
60 days
Styrene Monomer
Ingestion
Some positive developmental data exist,
Rat
NOAEL 400
during
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 11 of
14
but the data are not sufficient for
classification
mg/kg/day
gestation
Styrene Monomer
Inhalation
Some positive developmental data exist,
but the data are not sufficient for
classification
Multiple
animal
species
NOAEL 2.1
mg/l
during
gestation
Limestone
Ingestion
Not toxic to development
Rat
NOAEL 625
mg/kg/day
premating &
during
gestation
Synthetic Crystalline-Free Silica Gel
Ingestion
Not toxic to female reproduction
Rat
NOAEL 509
mg/kg/day
1 generation
Synthetic Crystalline-Free Silica Gel
Ingestion
Not toxic to male reproduction
Rat
NOAEL 497
mg/kg/day
1 generation
Synthetic Crystalline-Free Silica Gel
Ingestion
Not toxic to development
Rat
NOAEL
1,350
mg/kg/day
during
organogenesi
s
Target Organ(s)
Specific Target Organ Toxicity - single exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Styrene Monomer
Inhalation
auditory system
Causes damage to organs
Multiple
animal
species
LOAEL 4.3
mg/l
not available
Styrene Monomer
Inhalation
liver
Causes damage to organs
Mouse
LOAEL 2.1
mg/l
not available
Styrene Monomer
Inhalation
central nervous
system depression
May cause drowsiness or
dizziness
Human
NOAEL Not
available
occupational
exposure
Styrene Monomer
Inhalation
respiratory irritation
Some positive data exist, but the
data are not sufficient for
classification
Human
and
animal
NOAEL Not
available
Styrene Monomer
Inhalation
endocrine system
All data are negative
Rat
NOAEL Not
available
not available
Styrene Monomer
Inhalation
kidney and/or
bladder
All data are negative
Multiple
animal
species
NOAEL 2.1
mg/l
not available
Limestone
Inhalation
respiratory system
All data are negative
Rat
NOAEL
0.812 mg/l
90 minutes
Specific Target Organ Toxicity - repeated exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Talc
Inhalation
pneumoconiosis
Causes damage to organs
through prolonged or repeated
exposure
Human
NOAEL Not
available
occupational
exposure
Talc
Inhalation
pulmonary fibrosis |
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 18
mg/m3
113 weeks
Styrene Monomer
Inhalation
eyes
Causes damage to organs
through prolonged or repeated
exposure
Human
NOAEL Not
available
occupational
exposure
Styrene Monomer
Inhalation
auditory system
May cause damage to organs
though prolonged or repeated
exposure
Multiple
animal
species
NOAEL 1.3
mg/l
not available
Styrene Monomer
Inhalation
liver
May cause damage to organs
though prolonged or repeated
exposure
Mouse
LOAEL 0.85
mg/l
13 weeks
Styrene Monomer
Inhalation
nervous system
Some positive data exist, but the
data are not sufficient for
classification
Multiple
animal
species
LOAEL 1.1
mg/l
not available
Styrene Monomer
Inhalation
hematopoietic
system
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 0.85
mg/l
7 days
Styrene Monomer
Inhalation
endocrine system
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 0.6
mg/l
10 days
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 12 of
14
Styrene Monomer
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Multiple
animal
species
LOAEL 0.09
mg/l
not available
Styrene Monomer
Inhalation
heart | bone, teeth,
nails, and/or hair |
muscles | kidney
and/or bladder
All data are negative
Multiple
animal
species
NOAEL 4.3
mg/l
2 years
Styrene Monomer
Ingestion
nervous system
Some positive data exist, but the
data are not sufficient for
classification
Rat
LOAEL 500
mg/kg/day
8 weeks
Styrene Monomer
Ingestion
immune system
Some positive data exist, but the
data are not sufficient for
classification
Multiple
animal
species
NOAEL Not
available
not available
Styrene Monomer
Ingestion
liver | kidney and/or
bladder
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 677
mg/kg/day
6 months
Styrene Monomer
Ingestion
hematopoietic
system
Some positive data exist, but the
data are not sufficient for
classification
Dog
NOAEL 600
mg/kg/day
470 days
Styrene Monomer
Ingestion
heart | respiratory
system
All data are negative
Rat
NOAEL 35
mg/kg/day
105 weeks
Oxide Glass Chemicals
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Human
NOAEL not
available
occupational
exposure
Limestone
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Human
NOAEL Not
available
occupational
exposure
Synthetic Crystalline-Free
Silica Gel
Inhalation
respiratory system |
silicosis
All data are negative
Human
NOAEL Not
available
occupational
exposure
Titanium Dioxide
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Rat
LOAEL
0.010 mg/l
2 years
Titanium Dioxide
Inhalation
pulmonary fibrosis
All data are negative
Human
NOAEL Not
available
occupational
exposure
Quartz Silica
Inhalation
silicosis
Causes damage to organs
through prolonged or repeated
exposure
Human
NOAEL Not
available
occupational
exposure
Aspiration Hazard
Name
Value
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
Ecotoxicological information
Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Incinerate in a permitted waste incineration facility. As a disposal alternative, utilize an acceptable permitted waste disposal
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 13 of
14
facility. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical
substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated &
disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective
regulating authorities to determine the available treatment and disposal facilities.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. US Federal Regulations
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient
C.A.S. No
% by Wt
Styrene Monomer
100-42-5
10 - 30
15.2. State Regulations
Contact 3M for more information.
California Proposition 65
Ingredient
C.A.S. No.
Classification
SILICA, CRYSTALLINE (AIRBORNE
PARTICLES OF RESPIRABLE SIZE)
None
Carcinogen
Titanium Dioxide
13463-67-7
Carcinogen
WARNING: This product contains a chemical known to the State of California to cause cancer.
15.3. Chemical Inventories
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
15.4. International Regulations
Contact 3M for more information.
This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: Other information
NFPA Hazard Classification
Health: 2 Flammability: 3 Instability: 1 Special Hazards: None
background image
3M™ 3M Lightweight Body Filler PNs 05800, 05801, 05804, 05805
04/14/14
__________________________________________________________________________________________
Page 14 of
14
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Document Group:
32-1433-5
Version Number:
3.00
Issue Date:
04/14/14
Supercedes Date:
05/16/13
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable
for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available
directly from 3M
3M USA SDSs are available at www.3M.com
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 1 of
11
Safety Data Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
29-5993-0
Version Number:
3.02
Issue Date:
02/21/14
Supercedes Date:
10/02/12
SECTION 1: Identification
1.1. Product identifier
Cream Hardener (Red, White & Blue)
Product Identification Numbers
LB-K100-0965-7, LB-K100-0965-8, LB-K100-0965-9, LB-K100-0966-0, LB-K100-0966-1, LB-K100-0966-2, LB-K100-
0966-3, LB-K100-1035-6, LB-K100-1045-4, LB-K100-1286-7, 41-0003-7987-9, 60-4550-6614-6, 60-4550-6617-9, 60-4550-
6830-8, 60-4550-6981-9, 60-4550-6982-7, 60-4550-8123-6
1.2. Recommended use and restrictions on use
Recommended use
Automotive
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Automotive Aftermarket
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200.
This information may be different from the actual product label information for labels regulated by other agencies.
2.1. Hazard classification
Organic Peroxide: Type E.
Serious Eye Damage/Irritation: Category 2A.
Skin Sensitizer: Category 1.
2.2. Label elements
Signal word
Warning
Symbols
Flame | Exclamation mark |
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 2 of
11
Pictograms
Hazard Statements
Heating may cause a fire.
Causes serious eye irritation.
May cause an allergic skin reaction.
Precautionary Statements
General:
Keep out of reach of children.
Prevention:
Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
Keep away from clothing and other combustible materials.
Keep only in original container.
Avoid breathing dust/fume/gas/mist/vapors/spray.
Wear protective gloves and eye/face protection.
Wash thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Response:
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
If eye irritation persists: Get medical advice/attention.
IF ON SKIN: Wash with plenty of soap and water.
If skin irritation or rash occurs: Get medical advice/attention.
Wash contaminated clothing before reuse.
Storage:
Protect from sunlight.
Store at temperatures not exceeding 32C/90F. Keep cool.
Store away from other materials.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
Notes to Physician:
Not applicable
2.3. Hazards not otherwise classified
None.
6% of the mixture consists of ingredients of unknown acute dermal toxicity.
14% of the mixture consists of ingredients of unknown acute inhalation toxicity.
SECTION 3: Composition/information on ingredients
Ingredient
C.A.S. No.
% by Wt
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 3 of
11
Benzoyl Peroxide
94-36-0
30 - 60 Trade Secret *
Water
7732-18-5
10 - 30 Trade Secret *
Benzoic Acid, C9-11-Branched Alkyl Esters
131298-44-7
10 - 30 Trade Secret *
Zinc Stearate
557-05-1
3 - 7 Trade Secret *
Oxirane, Polymer with Methyloxirane, Monobutyl Ether 9038-95-3
1 - 5 Trade Secret *
Calcium Sulfate
7778-18-9
1 - 5 Trade Secret *
Iron Oxide (FE2O3)
1309-37-1
1 - 5 Trade Secret *
Ferric Ferrocyanide
14038-43-8
0 - 1 Trade Secret *
Ferric Ammonium Ferrocyanide
25869-00-5
0 - 1 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop,
get medical attention.
Eye Contact:
Immediately flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. Get medical
attention.
If Swallowed:
Rinse mouth. If you feel unwell, get medical attention.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2. Special hazards arising from the substance or mixture
Closed containers exposed to heat from fire may build pressure and explode. Part of the oxygen for combustion is supplied
by the peroxide itself.
5.3. Special protective actions for fire-fighters
No unusual fire or explosion hazards are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Eliminate all ignition sources if safe to do so. Keep away from heat/sparks/open flames/hot surfaces. - No
smoking. Use only non-sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces,
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 4 of
11
provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning!
A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Refer to
other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and
personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible
using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person.
Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container.
Dispose of collected material as soon as possible.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Avoid breathing of dust created by cutting, sanding, grinding or machining. Do not use in a confined area with minimal air
exchange. Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Avoid
breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when
using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the
workplace. Avoid release to the environment. Wash contaminated clothing before reuse.
7.2. Conditions for safe storage including any incompatibilities
Keep container tightly closed. Protect from sunlight. Store away from heat. Store at temperatures not exceeding 32C/90F.
Keep cool. Keep only in original container. Store away from other materials. Keep/store away from clothing and other
combustible materials.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
Ingredient
C.A.S. No.
Agency
Limit type
Additional Comments
Iron Oxide (FE2O3)
1309-37-1
Amer Conf of
Gov. Indust.
Hyg.
TWA(respirable fraction):5
mg/m3
Iron Oxide (FE2O3)
1309-37-1
US Dept of
Labor - OSHA
TWA(as fume):10 mg/m3
CYANIDES
14038-43-8 US Dept of
Labor - OSHA
TWA(as CN):5 mg/m3
Skin Notation
Zinc Stearate
557-05-1
US Dept of
Labor - OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
Calcium Sulfate
7778-18-9
Amer Conf of
Gov. Indust.
Hyg.
TWA(inhalable fraction):10
mg/m3
Calcium Sulfate
7778-18-9
US Dept of
Labor - OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 5 of
11
Benzoyl Peroxide
94-36-0
Amer Conf of
Gov. Indust.
Hyg.
TWA:5 mg/m3
Benzoyl Peroxide
94-36-0
US Dept of
Labor - OSHA
TWA:5 mg/m3
Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists
American Indust. Hygiene Assoc : American Industrial Hygiene Association
Chemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended Guidelines
US Dept of Labor - OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Provide ventilation adequate to maintain dust concentration below minimum explosive concentrations. Use general dilution
ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control
dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Indirect Vented Goggles
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Nitrile Rubber
If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then
use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an
exposure assessment. The following protective clothing material(s) are recommended: Apron – Nitrile
Respiratory protection
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of
a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator
type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Solid
Specific Physical Form:
Viscous
Odor, Color, Grade:
Red paste with slight ester odor
Odor threshold
No Data Available
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 6 of
11
pH
No Data Available
Melting point
No Data Available
Boiling Point
No Data Available
Flash Point
111 ºC [Test Method: Estimated]
Evaporation rate
No Data Available
Flammability (solid, gas)
Organic Peroxide: Type E.
Flammable Limits(LEL)
Not Applicable
Flammable Limits(UEL)
Not Applicable
Vapor Pressure
Not Applicable
Vapor Density
Not Applicable
Density
1.2 g/cm3
Specific Gravity
1.2 [@ 25 ºC] [Ref Std: WATER=1]
Solubility in Water
Negligible
Solubility- non-water
No Data Available
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
No Data Available
Decomposition temperature
No Data Available
Viscosity
No Data Available
Hazardous Air Pollutants
0 % weight [Test Method: Calculated]
Volatile Organic Compounds
0 lb/gal [Test Method: calculated SCAQMD rule 443.1]
Volatile Organic Compounds
0 g/l [Test Method: calculated SCAQMD rule 443.1]
Volatile Organic Compounds
0 % weight [Test Method: calculated per CARB title 2]
Percent volatile
20 % [Details: Water is the volatile component]
VOC Less H2O & Exempt Solvents
0 g/l [Test Method: calculated SCAQMD rule 443.1]
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.
10.2. Chemical stability
Stable. Stable unless exposed to heat, flames and drying conditions.
10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Heat
10.5. Incompatible materials
Accelerators
10.6. Hazardous decomposition products
Substance
Condition
Carbon monoxide
Not Specified
Carbon dioxide
Not Specified
Toxic Vapor, Gas, Particulate
Not Specified
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 7 of
11
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
May be harmful if inhaled.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge,
headache, hoarseness, and nose and throat pain.
Skin Contact:
May be harmful in contact with skin.
Contact with the skin during product use is not expected to result in significant irritation. Allergic Skin Reaction (non-photo
induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Eye Contact:
Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the
cornea, and impaired vision.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name
Route
Species
Value
Overall product
Dermal
No data available; calculated ATE 4,339.3 mg/kg
Overall product
Inhalation-
Dust/Mist(4
hr)
No data available; calculated ATE 10.7 mg/l
Overall product
Ingestion
No data available; calculated ATE > 5,000 mg/kg
Benzoyl Peroxide
Dermal
LD50 estimated to be 2,000 - 5,000 mg/kg
Benzoyl Peroxide
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 > 24.3 mg/l
Benzoyl Peroxide
Ingestion
Rat
LD50 > 5,000 mg/kg
Benzoic Acid, C9-11-Branched Alkyl Esters
Dermal
Rabbit
LD50 > 2,000 mg/kg
Benzoic Acid, C9-11-Branched Alkyl Esters
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 2 mg/l
Benzoic Acid, C9-11-Branched Alkyl Esters
Ingestion
Rat
LD50 > 5,000 mg/kg
Zinc Stearate
Dermal
Rabbit
LD50 > 2,000 mg/kg
Zinc Stearate
Ingestion
Rat
LD50 > 5,000 mg/kg
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Dermal
Rabbit
LD50 > 16,960 mg/kg
Calcium Sulfate
Ingestion
Rat
LD50 > 5,000 mg/kg
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Inhalation-
Dust/Mist
(4 hours)
Rat
LC50 > 5 mg/l
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Ingestion
Rat
LD50 4,240 mg/kg
Iron Oxide (FE2O3)
Dermal
Not
available
LD50 3,100 mg/kg
Iron Oxide (FE2O3)
Ingestion
Not
available
LD50 3,700 mg/kg
Ferric Ammonium Ferrocyanide
Ingestion
Rat
LD50 > 5,110 mg/kg
Ferric Ferrocyanide
Ingestion
Rat
LD50 > 8,000 mg/kg
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 8 of
11
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Name
Species
Value
Benzoyl Peroxide
Rabbit
Minimal irritation
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Rabbit
Minimal irritation
Iron Oxide (FE2O3)
Rabbit
No significant irritation
Serious Eye Damage/Irritation
Name
Species
Value
Benzoyl Peroxide
Rabbit
Severe irritant
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Rabbit
No significant irritation
Iron Oxide (FE2O3)
Rabbit
No significant irritation
Skin Sensitization
Name
Species
Value
Benzoyl Peroxide
Human
and
animal
Sensitizing
Iron Oxide (FE2O3)
Human
Some positive data exist, but the data are not
sufficient for classification
Respiratory Sensitization
Name
Species
Value
Germ Cell Mutagenicity
Name
Route
Value
Benzoyl Peroxide
In Vitro
Not mutagenic
Benzoyl Peroxide
In vivo
Not mutagenic
Iron Oxide (FE2O3)
In Vitro
Not mutagenic
Carcinogenicity
Name
Route
Species
Value
Benzoyl Peroxide
Ingestion
Multiple
animal
species
Not carcinogenic
Benzoyl Peroxide
Dermal
Mouse
Some positive data exist, but the data are not
sufficient for classification
Oxirane, Polymer with Methyloxirane, Monobutyl Ether
Ingestion
Rat
Not carcinogenic
Iron Oxide (FE2O3)
Inhalation
Human
Some positive data exist, but the data are not
sufficient for classification
Reproductive Toxicity
Reproductive and/or Developmental Effects
Name
Route
Value
Species
Test Result
Exposure
Duration
Benzoyl Peroxide
Ingestion
Not toxic to female reproduction
Rat
NOAEL
1,000
mg/kg/day
premating &
during
gestation
Benzoyl Peroxide
Ingestion
Some positive male reproductive data
exist, but the data are not sufficient for
classification
Rat
NOAEL 500
mg/kg/day
premating &
during
gestation
Benzoyl Peroxide
Ingestion
Some positive developmental data exist,
but the data are not sufficient for
classification
Rat
NOAEL 500
mg/kg/day
premating &
during
gestation
Oxirane, Polymer with Methyloxirane,
Monobutyl Ether
Ingestion
Not toxic to female reproduction
Rat
NOAEL
3,770
mg/kg/day
90 days
Oxirane, Polymer with Methyloxirane,
Monobutyl Ether
Ingestion
Not toxic to male reproduction
Rat
NOAEL
3,770
mg/kg/day
90 days
Oxirane, Polymer with Methyloxirane,
Inhalation
Some positive male reproductive data
Rat
NOAEL 1
2 weeks
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 9 of
11
Monobutyl Ether
exist, but the data are not sufficient for
classification
mg/l
Target Organ(s)
Specific Target Organ Toxicity - single exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Ingestion
nervous system
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL Not
available
Specific Target Organ Toxicity - repeated exposure
Name
Route
Target Organ(s)
Value
Species
Test Result
Exposure
Duration
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Inhalation
endocrine system |
hematopoietic
system | liver |
nervous system
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 1
mg/l
2 weeks
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Inhalation
kidney and/or
bladder
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL .005
mg/l
2 weeks
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Inhalation
respiratory system
Some positive data exist, but the
data are not sufficient for
classification
Rat
LOAEL .001
mg/l
2 weeks
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Inhalation
heart
All data are negative
Rat
NOAEL .5
mg/l
2 weeks
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Ingestion
liver | kidney and/or
bladder
Some positive data exist, but the
data are not sufficient for
classification
Rat
NOAEL 145
mg/kg/day
90 days
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Ingestion
hematopoietic
system
All data are negative
Rat
NOAEL 500
mg/kg/day
2 years
Oxirane, Polymer with
Methyloxirane, Monobutyl
Ether
Ingestion
heart | endocrine
system | respiratory
system
All data are negative
Rat
NOAEL
3,770
mg/kg/day
90 days
Iron Oxide (FE2O3)
Inhalation
pulmonary fibrosis |
pneumoconiosis
Some positive data exist, but the
data are not sufficient for
classification
Human
NOAEL Not
available
occupational
exposure
Aspiration Hazard
Name
Value
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
Ecotoxicological information
Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.
SECTION 13: Disposal considerations
13.1. Disposal methods
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 10 of
11
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Incinerate uncured product in a permitted waste incineration facility. Proper destruction may require the use of additional
fuel during incineration processes. Empty drums/barrels/containers used for transporting and handling hazardous chemicals
(chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored,
treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the
respective regulating authorities to determine the available treatment and disposal facilities.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. US Federal Regulations
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - Yes
Immediate Hazard - Yes
Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient
C.A.S. No
% by Wt
Zinc Stearate (ZINC COMPOUNDS)
557-05-1
3 - 7
Benzoyl Peroxide
94-36-0
30 - 60
Ferric Ferrocyanide (CYANIDES)
14038-43-8
0 - 1
15.2. State Regulations
Contact 3M for more information.
15.3. Chemical Inventories
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
15.4. International Regulations
Contact 3M for more information.
This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: Other information
NFPA Hazard Classification
Health: 2 Flammability: 2 Instability: 1 Special Hazards: Oxidizer
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
background image
Cream Hardener (Red, White & Blue)
02/21/14
__________________________________________________________________________________________
Page 11 of
11
HMIS Hazard Classification
Health: 2 Flammability: 1 Physical Hazard: 1 Personal Protection: X - See PPE section.
Hazardous Material Identification System (HMIS® III) hazard ratings are designed to inform employees of chemical hazards
in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use
and are not intended for use in emergency situations. HMIS® III ratings are to be used with a fully implemented HMIS® III
program. HMIS® is a registered mark of the American Coatings Association (ACA).
Document Group:
29-5993-0
Version Number:
3.02
Issue Date:
02/21/14
Supercedes Date:
10/02/12
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable
for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available
directly from 3M
3M USA SDSs are available at www.3M.com